General:
Number of channels 4
Max. total output all channels driven 10000 W
Max. output voltage per channel 150 Vpeak
Max. output current per channel 38 Arms
Max. Output Power 2 ohms 4 ohms 8 ohms 16 ohms
Per ch. (all ch.’s driven) 2500 W 2100 W 1300 W 660 W
Bridged - 3) 5000 W 4200 W 2600 W
Performance with Gain: 35 dB and VPL: 150 V
THD 20 Hz - 20 kHz for 1 W <0,1%
THD at 1 kHz and 1 dB below clipping <0,05%
Signal To Noise Ratio >112 dBA
Channel separation (Crosstalk) at 1 kHz >70 dB
Frequency response (1 W into 8 Ohm) +0/-3 dB 6.8 Hz - 34 kHz
Voltage Peak Limiter (VPL), max. peak output
VPL, selectable per ch. (V) 150, 121, 101, 83, 70, 56, 47, 38 V
VPL, selectable when bridged (V) 1) 300, 242, 202, 166, 140, 112, 94, 76 V
Voltage Peak Limiter mode (per ch.) Hard / Soft
Gain and Level
Amplifier gain selectable (all channels) 1) Rear-panel switches: 23, 26, 29, 32, 35, 38, 41, 44 dB
Default gain 35 dB
Level adjustment (per ch.) Front-panel potentiometer, 21 position detented from -inf to 0 dB
Connectors and Switches
Input+Link connectors (per ch.) 3-pin XLR, electronically balanced
Output connectors (per ch.) Neutrik Speakon or Binding Posts (must be specified upon order)
Output bridge mode Connect Ch. A/C+ and Ch. B/D- . Ch. A/C are signal input sources
NomadLink® network On board, 2 x RJ45 EtherCon connectors, IN and OUT
Intelligent fans (on/off) Yes, depending on presence of output signal
Power on/off and Remote enable on/off ndividual switches on front-panel
Cooling Two fans, front-to-rear airflow, temperature controlled speed
Front-panel indicators:
Common NomadLink® Network; Power Average Limiter (PAL) 2); Power on
Per channel Signal present/High-impedance; -20 dB, -15 dB, -10 dB and -4 dB
output signal; Voltage Peak Limiter (VPL);
Current Peak Limiter (CPL): Very High Frequency (VHF);
High temperature; Mute
Power
Operating voltage, 230 V / 115 V nominal 4) 130-265 V / 65-135 V
Minimum power-up voltage, 230 V / 115 V 171 V / 85 V
Power Average Limiter (PAL) 2) Yes
Soft start / Inrush Current Draw Yes / max. 5 A
Dimensions (W/H/D) W: 483 mm (19”), H: 88 mm (2 U), Overall D: 396 mm (15.6”),
Mounting D: 358 mm (14.1”)
Weight 12 kg (26.4 lbs.)
Finish Black painted steel chassis with black painted steel / aluminum front
Approvals CE, ANSI/UL 60065 (ETL), CSA C22.2 NO. 60065, FCC
Mains plug type 230 V CE: 16 A, CEE7; 115 V ETL: 30 A Twist lock
Note 1): Automatic -6 dB gain compensation when bridging channels. Ch.’s A+B and C+D can be bridged.
Note 2): PAL can reduce the maximum output power to keep the power supply operating safely,
and/or to prevent excessive current draw tripping the mains breaker.
Refer to Operation Manual.
Note 3): The amplifier will be fully operational at bridge-mode 2 ohm loads,
but due to physical constraints in the construction, the max. output power will not be significantly higher than running
individual channels and therefore not stated here.
Note 4): Separate 230 V or 115 V versions available. Not selectable on the amplifier.
All specifications are subject to change without notice.